Difference between revisions of "OpenerPCR"
(Genesis) |
(Electronics BOM, Opener PCR) |
||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Components | Components | ||
Active/passive components | Active/passive components | ||
| Line 36: | Line 31: | ||
1 Custom Peltier, Qmax = 84 W, dT = 78 K, Imax = 7.8 A Can one less powerful be used [http://grobotronics.com/thermoelectric-cooler-40x40mm.html] | 1 Custom Peltier, Qmax = 84 W, dT = 78 K, Imax = 7.8 A Can one less powerful be used [http://grobotronics.com/thermoelectric-cooler-40x40mm.html] | ||
| − | 1 US Sensor USP11553 rev none Thermistor / PTC [http://grobotronics.com/thermistor-10k.html] | + | 1 US Sensor USP11553 rev none Thermistor / PTC, ''Reprap'', [http://grobotronics.com/thermistor-10k.html] |
| + | |||
| + | 1 Custom Kapton Heater, 25 W, 11.3 V, ''Reprap'', 12V 40W [http://grobotronics.com/reprap-12v-40w-ceramic-cartridge-heater.html] | ||
| − | + | Where does the 4 channel Relay Module fit in? [http://grobotronics.com/relay-module-4-channel.html] | |
'''Autonomous parts''' | '''Autonomous parts''' | ||
| Line 46: | Line 43: | ||
Number Part What we really bought | Number Part What we really bought | ||
| − | 1 Arduino Uno Replace with Arduino Mega clone, from RepRap project | + | 1 Arduino Uno Replace with Arduino Mega clone, "from RepRap project" |
1 MicroATX power supply, 200 W, 14 A on 12 V rail, fan temperature control disabled, 24 pin ATX connector only | 1 MicroATX power supply, 200 W, 14 A on 12 V rail, fan temperature control disabled, 24 pin ATX connector only | ||
Revision as of 19:17, 12 September 2014
Components Active/passive components Brand official Serial Description SMD What we really bought
2 Yageo SQP10AJB-4R7 Resistor, 4.7 Ohm, 10 W No Conrad
Sparkfun Resistor Kit, and other 1/4W resistors? Where can they NOT be used
1 Panasonic ERG-2SJ160 Resistor, 16 Ohm No 3 resistors circuit: (10 + 22) + 10
2 Yageo MFP-25BRD52-2K2 Resistor, 2.2k Ohm, 0.1% No Resistor, 2.2k Ohm, 1%
1 Tyco 282834-6 Terminal block, 6 connector No
2 Panasonic ERJ-3GEYJ332V Resistor, 3.3k Ohm Yes 3 resistors circuit: (22K + 22K) + 22
4 Panasonic ERJ-3GEYJ102V Resistor, 1k Ohm Yes As is
1 Panasonic ERG-1SJ510 Resistor, 51 Ohm, 1 W No Okaphone: Resistor, 56 Ohm, 1 W
1 Fairchild RFD3055LE Transistor, MOSFET N-Ch No
1 Microchip MCP3551-E/SN ADC, 22 bit No Okaphone
1 Panasonic ECA-1CM332 Capacitor, 3300 uF No Conrad
1 Panasonic ECA-1CM102 Capacitor, 1000 uF No Conrad
1 ST VNH3SP30 H-Bridge IC Yes Okaphone
1 Custom Peltier, Qmax = 84 W, dT = 78 K, Imax = 7.8 A Can one less powerful be used [1]
1 US Sensor USP11553 rev none Thermistor / PTC, Reprap, [2]
1 Custom Kapton Heater, 25 W, 11.3 V, Reprap, 12V 40W [3]
Where does the 4 channel Relay Module fit in? [4]
Autonomous parts
Things to connect components with/on/to
Number Part What we really bought
1 Arduino Uno Replace with Arduino Mega clone, "from RepRap project"
1 MicroATX power supply, 200 W, 14 A on 12 V rail, fan temperature control disabled, 24 pin ATX connector only
1 Ribbon cable, 16 pin, female - female, 24"
1 LCD, HD44780 compatible, 20 chars, 4 rows, blue backlight [5]
1 PCB Etched, WANT
1 USB Cable, A to B, 6 feet
1 PSU Power Cord, USA plug, 6 feet
